Firmware Release Notification: Version 1.0.9

v Relevant Products:

SBM-GEM-X2C\+

SSE-G24-TG4

SSE-G48-TG4

v Noticeable Improvements from version 1.0.7-7 to 1.0.9:

1) Fixed MAC Address table display for beyond 1K MAC addresses.

2) Fixed several stacking related issues.

3) Improvement in switch boot-up time performance.

4) Fixed ACL feature configuration error, ACL Redirect functionality.

5) Adding “AOM-SSE-X2S” module support for SSE-G24-TG4 and SSE-G48-TG4.

v Level of Importance: Recommended. If you think any of the above-mentioned function/feature improvements are relevant to your operation, this firmware upgrade is recommended.

v àImportant Information: If your system is currently running a version lower than 1.0.7-7, it is critical that you reset the switch to factory defaults before upgrading the firmware to 1.0.7-7 or 1.0.9. The switch will then need to be reconfigured upon upgrade. The startup configuration files (iss.conf) are not compatible between pre-1.0.7-7 and post-1.0.7-7 firmware releases.

v Upgrade Instructions:

- Download the file “switch_firmware_1.0.9.zip” (https://www.supermicro.com/wdl/Firmware/Switch/SBM-GEM-X2C_SSE-G24-TG4_SSE-G48-TG4/Release-1.0.9/);

- Unzip and extract “switch_firmware_1.0.9.bin” to the folder your tftp server points to.

- Follow instructions in the user manual (http://www.supermicro.com/manuals/other/SM-CLI-Guide.pdf Section 3.31 on page 70.) for firmware upgrade procedures.

-

v Previous Release: Version 1.0.7-7

- This version can be downloaded here: https://www.supermicro.com/wdl/Firmware/Switch/SBM-GEM-X2C_SSE-G24-TG4_SSE-G48-TG4/Release-1.0.7-7/

- #######################################################################
- The information in this readme file has been carefully reviewed and is believed to be accurate. 
- The vendor assumes no responsibility for any inaccuracies that may be contained in this document, 
- makes no commitment to update or to keep current the information in this manual, or to notify 
- any person or organization of the updates. 
-  
- Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product 
- described in this manual at any time and without notice. This product, including software 
- and documentation, is the property of Supermicro and/or its licensors, and is supplied only 
- under a license. Any use or reproduction of this product is not allowed, except as expressly 
- permitted by the terms of said license.
- IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE 
- OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, 
- EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE 
- LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE 
- COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, 
- OR DATA.
- Any disputes arising between manufacturer and customer shall be governed by the laws of 
- Santa Clara County in the State of California, USA. The State of California, County of Santa Clara 
- shall be the exclusive venue for the resolution of any such disputes. Supermicro's total 
- liability for all claims will not exceed the price paid for the hardware product.
-  
- Copyright © 2010 by SUPER MICRO COMPUTER INC.
- All rights reserved.