 |
|
 |
| MBD-X6DH8-XB-O |
- X6DH8-XB (Standard Retail Pack)
|
| MBD-X6DH8-XB-B |
|
| |
|
| Form Factor |
|
| Dimensions |
- 12" x 13.05" (30.5cm x 33.2cm)
|
| |
|
| CPU |
- Dual 604-pin FC-mPGA4 Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Xeon (Nocona) CPU with 1MB L2 Integrated Advanced Transfer Cache, up to 3.60 GHz
- Xeon (Irwindale) CPU with 2MB L2 Integrated Advanced Transfer Cache, up to 3.80 GHz
- Xeon LV (Low Voltage) CPU, up to 2.8 GHz
|
| System Bus |
|
| Operating System Software |
|
| |
|
| Memory Capacity |
- Eight 184-pin DIMM sockets
- Supports up to 16 GB DDR 333 MHz memory or
- Supports up to 32 GB DDR 266 MHz memory
- Dual channel memory bus
- Memory must be populated in pairs
- Single-rank modules are recommended for 6+ DIMM support
|
| Memory Type |
- DDR333/266 buffered (registered) ECC SDRAM 72-bit, 184-pin gold-plated DIMMs
|
| DIMM Sizes |
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC buffered/registered memory)
- Supports Intel® x4 Single Device Data Correction (SDDC)
|
| |
|
| Chipset |
- Intel® E7520 chipset
- ICH5R + PXH + BCM5721
|
| SATA |
- ICH5R SATA Controller
- RAID 0, 1, JBOD support
|
| SCSI |
- Adaptec AIC-7902 Controller
- Dual-Channel Ultra320 SCSI (Host RAID only supports 4 drives)
- Host RAID 0, 1, 10, JBOD support
|
| RAID |
|
| IPMI |
|
| Network Controllers |
- Dual Broadcom BCM5721 Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
|
| Graphics |
- ATI Rage XL SVGA PCI video controller with 8 MB of video memory
|
| Super I/O |
|
| Clock Generator |
|
| |
|
| Serial ATA |
- Two Serial ATA ports
- Two SATA hard drives supported
|
| IDE |
- Dual EIDE channels support up to four UDMA IDE devices
- Supports ATA/100
|
| Floppy |
- 1 Floppy controller; 1.44 MB
|
| LAN |
|
| USB |
- 2x USB rear ports
- 1x USB internal dual header supports up to 2 USB ports
- 1x USB internal header supports single USB port
- USB 2.0 Compliant
|
| VGA |
|
| Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial Ports |
- 2 Fast UART 16550 serial ports
|
|
|
|
|
| 2U |
|
| 3U |
|
| Tower / 4U Rackmount |
|
| Important Chassis Notes |
- To ensure system stability, a 420W (minimum) ATX power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin are required]
- Chassis must have CPU mounting holes required for 800MHz FSB CPUs with this serverboard.
|
| |
|
| PCI-Express |
- 1 (x4) signal on a (x8) PCI-e slot
|
| PCI-X |
- 2x 64-bit 133/100MHz PCI-X (3.3V) slots
- 4x 64-bit 100MHz PCI-X (3.3V) slots
|
| |
|
| BIOS Type |
- 8Mb Flash EEPROM with Phoenix® BIOS
|
| BIOS Features |
- Plug and Play (PnP)
- SMBIOS 2.3
- USB Keyboard Support
- DMI 2.3
- ACPI 1.0
- SMBIOS 2.3
- RTC (Real Time Clock) Wakeup
|
| |
|
| Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0
- Super
 Doctor III
- Watch Dog
- NMI
|
| Power Configurations |
- ACPI/APM Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode control for AC power loss recovery
|
| |
|
| CPU |
- Monitors for CPU Cores, +1.8V, +3.3V, +5V, ±12V, +3.3V Standby & +5V Standby, VBAT
- CPU Core 4-Phase-switching voltage regulator with auto-sense from 1.3V-1.5V
|
| FAN |
- Total of four 4-pin fan headers, four 3-pin fan headers
- 8x fans with status monitoring
- Status monitor with firmware/software on/off control
- Support 3-pin fans (without speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
|
| Temperature |
- Monitoring for CPU, chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) Support
|
| LED |
- CPU / System Overheat LED
|
| Other Features |
- Chassis intrusion detection
- Chassis intrusion header
- SDDC support
|
|
