 | |
 | | MBD-X6DVL-EG2-O | - X6DVL-EG2 (Standard Retail Pack)
| | | |
| | Form Factor | | | Dimensions | - 12" length x 10" width
(30.5cm x 25.4cm) - PCB height: 0.062"(62mil)
- Board height: 0.041"(41mil)
| | | |
| | CPU | - Dual 604-pin FC-mPGA4 Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Xeon (Nocona) CPU with 1MB L2 Integrated Advanced Transfer Cache, up to 3.60 GHz
- Xeon (Irwindale) CPU with 2MB L2 Integrated Advanced Transfer Cache, up to 3.80 GHz
- Xeon LV (Low Voltage) CPU, up to 2.8 GHz
| | System Bus | | | Operating System Software | | | | |
| | Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB DDR-II 400MHz memory
- Dual channel memory bus
- Memory must be populated in pairs
| | Memory Type | - DDR2 400MHz registered ECC buffered SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | | | Memory Voltage | | | Error Detection | - Supports Single Device Data Correction (SDDC)
| | | |
| | Chipset | - Intel® E7320 chipset
- MCH + 6300ESB + 82541GI
| | SATA | - 6300ESB (Hance Rapids) SATA Controller (2x Drive support)
- 2x SATA Ports
- RAID 0, 1 support
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- (Optional:AOC-IPMI20-E ) Card not included.
| | Network Controllers | - Dual Intel® 82541GI
Single Port Gigabit Controller - Support for 10Base-T, 100Base-TX, 1000BASE-T, and 2x RJ45
| | Graphics | - ATI Rage XL SVGA PCI video controller with 8 MB of video memory
| | Super I/O | | | Clock Generator | | | | |
| | Serial ATA | - Two Serial ATA ports
- Two SATA hard drives supported
| | IDE | - Dual EIDE channels support up to four UDMA / IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
| | Floppy | - 1 Floppy controller; 1.44 MB support
| | LAN | | | USB | - 2x USB rear ports
- 1x USB internal header for 2 ports
- USB 2.0 Compliant / 1.1 Compliant
| | VGA | | | Keyboard / Mouse | - PS/2 keyboard and mouse ports
| | Serial Port / Header | - 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
| | | | | | 1U | | | Tower / 4U Rackmount | | | Important Chassis Notes | - To ensure system stability, a 420W (minimum) ATX 12V/EPS12V power supply [4-pin (+12V), 8-pin (+12V) and 24-pin] is required for systems built with non-Supermicro chassis / power supplies.
- Chassis must have CPU mounting holes required for 800MHz FSB CPUs with this serverboard.
| | | | | PCI-Express | | | PCI | - 1x 64-bit 66MHz PCI (3.3V) slot
- (PCI-X cards are not supported in this slot)
| | PCI | - 3x 32-bit 33MHz PCI (5V) slots
| | | | | BIOS Type | - 8Mb Flash EEPROM with AMI® BIOS (SST)
| | BIOS Features | - Plug and Play (PnP)
- ACPI 1.0
- APM 1.2
- DMI 2.3
- PCI 2.2
- SMBIOS 2.3
- Hardware BIOS Virus protection
- USB Keyboard Support
| | | | | Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
| | Power Configurations | - ACPI/APM Power Management
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Main Switch Override Mechanism
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
| | | | | Voltage | - Monitors for CPU Cores +3.3V, +5V, ±12V & +5V Standby
- CPU Core 3-Phase-switching voltage regulator with auto-sense from 0.83V-1.61V
- Adjustable CPU clock frequency ratio
| | FAN | - Total of six 4-pin fan headers
- 6x fans with status tachometer monitoring
- Status monitor for on/off control
- Status monitor for speed control
- Support for 3-pin fan and 4-pin fan speed control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
| | Temperature | - Monitoring for CPU, chassis environment
- CPU thermal trip support
- Thermal Control for 6x Fan Connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
| | LED | - CPU / System Overheat LED
- Suspend-state indicator LED
- +5V Standy Alert LED
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
| |
