| | SYS-5015TB-10GB | - SuperServer 5015TB-10GB (Black)
| | | CPU | - Single LGA775 ZIF Socket
- Supports Quad-Core Intel® Xeon® X3300/X3200 series
- Supports Dual-Core Intel® Xeon® E3100/3000 series
- Supports Intel® Xeon® processor L3360 and L3110 series
- Supports Intel® Core™2 Quad Q9000/Q8000/Q6000 series
- Supports Intel® Core™2 Duo E8000/E7000/E6000/E4000 series
- Supports Intel® Pentium® E5000/E2000 series
- Supports Intel® Celeron® E1000 and 400 series
- NOTE: 1600MHz CPU has to use 1600 MHz XMP Memory
| System Bus | - 1600 / 1333 / 1066 / 800 MHz system bus
| | | Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered, non-ECC DDR3 1333/1066/800MHz memory (Dual Channel) or up to 4 GB Non-ECC 1600MHz XMP DDR3 memory
| Memory Type | - DDR3 1333/1066/800MHz unbuffered, non-ECC SDRAM, 240-pin gold-plated DIMMs or Non-ECC 1600MHz XMP DDR3 memory
| DIMM Sizes | - 256 MB, 512 MB, 1 GB, 2 GB
| Memory Voltage | | | | Chipset | - Intel X48 chipset
- ICH9R + Intel® 82573V + Intel® 82573L
| Serial ATA | - Intel® ICH9R SATA controller built-in (3 Gbps)
- RAID 0, 1, 5, 10 (Windows)
- RAID 0, 1, 10 (Linux)
| IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN & optional KVM-over-LAN support
- SIMSO Slot - Supermicro Intelligement Management
- (Optional: AOC-SIMSO-HTC, AOC-SIMSO+)
- NOTE: AOC-SIMSO+ must use Dedicated LAN for KVM-over-LAN function
| Network Controllers | - Intel® 82598EB 10 Gigabit Ethernet Controller with CX4 interface
- Intel® 82573V & 82573L Gigabit Ethernet Controllers
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
| VGA | - On-board XGI Volari Z9S (32MB) graphics
| Super I/O | | Clock Generator | | | | Serial ATA | - Four Serial ATA ports (3 Gbps performance)
- Four SATA hard drives supported
| LAN | | USB | - Up to 8x USB 2.0 / 1.1 compliant ports
- 2 rear ports + 2 internal headers + 2 Type A ports
| VGA | | Serial Ports | - 1x Fast UART 16550 serial port
- 1x internal header
| | | BIOS Type | - 16Mb Flash EEPROM with Phoenix BIOS
| BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0 / 2.0 (S3 Optional)
- ACPI 1.0 (limited)
- USB Keyboard support
- Hardware BIOS Virus protection
| | | | | Form Factor | | Model | | | | Height | | Width | | Depth | | Gross Weight | | Available Colors | | | | Buttons | - Power On/Off button
- System Reset button
| LEDs | - Power LED
- Hard drive activity LED
- 2x Network activity LEDs
- System Overheat LED
| | | PCI-Express | - 1 (x16) PCI-e 2.0 slot (Low Profile)
| | | Hot-swap | - 2x 3.5" SATA Hot-swap drive bays
| | | 1U SATA Backplane | | | Fans | | | | 780W AC to DC power supply w/ PFC | AC Input | - 100-240V, 60-50Hz, 9.5-3.5Amp
| +5V sb | | +12V | - 65 Amp @ 180-240Vac
- 58 Amp @ 100-140Vac
| | | Software | | Power Configurations | - ACPI / ACPM Power Management
- Main Switch Override Mechanism
- Keyboard Wakeup from Soft-Off
- CPU Fan auto-off in sleep mode
- Power-on mode control for AC power loss recovery
| | | CPU | - Monitors for CPU Cores ( +1.8V, +3.3V, +5, ±12V, +3.3V Standby, +5V Standby, VBAT, HT, Memory, Chipset)
- CPU Core 5-Phase-switching voltage regulator with auto-sense from 0.3750V-1.6000V
| FAN | - Total of three 4-pin fan headers
- 3x fans with tachometer monitoring
- Status monitor with firmware / software speed control
- Status monitor for on/off control
- Low noise fan speed control
| Temperature | - Monitoring for CPU and chassis environment
- CPU Thermal Trip support
- Thermal Control for 8x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor (TM2) Support
- PECI
| LED | - CPU / System Overheat LED
- Suspend-state indicator LED
| | | Environmental Specifications | - Operating Temperature:
10°C to 35°C (50°F to 95°F) - Non-operating Temperature:
-40°C to 70°C (-40°F to 158°F) - Operating Relative Humidity:
8% to 90% (non-condensing) - Non-operating Relative Humidity:
5% to 95% (non-condensing) | |