 |
|
 |
| MBD-X6DVL-EG2-O |
- X6DVL-EG2 (Standard Retail Pack)
|
| |
|
|
| Form Factor |
|
| Dimensions |
- 12" length x 10" width
(30.5cm x 25.4cm)
- PCB height: 0.062"(62mil)
- Board height: 0.041"(41mil)
|
| |
|
|
| CPU |
- Dual 604-pin FC-mPGA4 Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Xeon (Nocona) CPU with 1MB L2 Integrated Advanced Transfer Cache, up to 3.60 GHz
- Xeon (Irwindale) CPU with 2MB L2 Integrated Advanced Transfer Cache, up to 3.80 GHz
- Xeon LV (Low Voltage) CPU, up to 2.8 GHz
|
| System Bus |
|
| Operating System Software |
|
| |
|
|
| Memory Capacity |
- Four 240-pin DIMM sockets
- Supports up to 8 GB DDR-II 400MHz memory
- Dual channel memory bus
- Memory must be populated in pairs
|
| Memory Type |
- DDR2 400MHz registered ECC buffered SDRAM 72-bit, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
|
| Memory Voltage |
|
| Error Detection |
- Supports Single Device Data Correction (SDDC)
|
| |
|
|
| Chipset |
- Intel® E7320 chipset
- MCH + 6300ESB + 82541GI
|
| SATA |
- 6300ESB (Hance Rapids) SATA Controller (2x Drive support)
- 2x SATA Ports
- RAID 0, 1 support
|
| IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- (Optional:AOC-IPMI20-E ) Card not included.
|
| Network Controllers |
- Dual Intel® 82541GI
Single Port Gigabit Controller
- Support for 10Base-T, 100Base-TX, 1000BASE-T, and 2x RJ45
|
| Graphics |
- ATI Rage XL SVGA PCI video controller with 8 MB of video memory
|
| Super I/O |
|
| Clock Generator |
|
| |
|
|
| Serial ATA |
- Two Serial ATA ports
- Two SATA hard drives supported
|
| IDE |
- Dual EIDE channels support up to four UDMA / IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
|
| Floppy |
- 1 Floppy controller; 1.44 MB support
|
| LAN |
|
| USB |
- 2x USB rear ports
- 1x USB internal header for 2 ports
- USB 2.0 Compliant / 1.1 Compliant
|
| VGA |
|
| Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial Port / Header |
- 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
|
|
|
|
|
| 1U |
|
| Tower / 4U Rackmount |
|
| Important Chassis Notes |
- To ensure system stability, a 420W (minimum) ATX 12V/EPS12V power supply [4-pin (+12V), 8-pin (+12V) and 24-pin] is required for systems built with non-Supermicro chassis / power supplies.
- Chassis must have CPU mounting holes required for 800MHz FSB CPUs with this serverboard.
|
| |
|
| PCI-Express |
|
| PCI |
- 1x 64-bit 66MHz PCI (3.3V) slot
- (PCI-X cards are not supported in this slot)
|
| PCI |
- 3x 32-bit 33MHz PCI (5V) slots
|
| |
|
| BIOS Type |
- 8Mb Flash EEPROM with AMI® BIOS (SST)
|
| BIOS Features |
- Plug and Play (PnP)
- ACPI 1.0
- APM 1.2
- DMI 2.3
- PCI 2.2
- SMBIOS 2.3
- Hardware BIOS Virus protection
- USB Keyboard Support
|
| |
|
| Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations |
- ACPI/APM Power Management
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Main Switch Override Mechanism
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
|
| |
|
| Voltage |
- Monitors for CPU Cores +3.3V, +5V, ±12V & +5V Standby
- CPU Core 3-Phase-switching voltage regulator with auto-sense from 0.83V-1.61V
- Adjustable CPU clock frequency ratio
|
| FAN |
- Total of six 4-pin fan headers
- 6x fans with status tachometer monitoring
- Status monitor for on/off control
- Status monitor for speed control
- Support for 3-pin fan and 4-pin fan speed control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
|
| Temperature |
- Monitoring for CPU, chassis environment
- CPU thermal trip support
- Thermal Control for 6x Fan Connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
|
| LED |
- CPU / System Overheat LED
- Suspend-state indicator LED
- +5V Standy Alert LED
|
| Other Features |
- Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
|
|
