 |
 |
MBD-X6DVA-4G2-O |
- X6DVA-4G2 (Standard Retail Pack)
|
MBD-X6DVA-4G2-B |
|
|
 |
Form Factor |
|
Dimensions |
- 12" x 10" (30.5cm x 25.4cm)
|
|
 |
CPU |
- Dual 604-pin FC-mPGA4 Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Xeon (Paxville) Dual Core CPU with 2x2MB L2 Integrated Advanced Transfer Cache
- Xeon (Nocona) CPU with 1MB L2 Integrated Advanced Transfer Cache, up to 3.60 GHz
- Xeon (Irwindale) CPU with 2MB L2 Integrated Advanced Transfer Cache, up to 3.80 GHz
- Xeon LV (Low Voltage) CPU, up to 2.8 GHz
|
System Bus |
|
Operating System Software |
|
|
 |
Memory Capacity |
- Six 240-pin DIMM sockets
- Supports up to 12 GB DDR2 400 MHz memory
- Dual channel memory bus
- Memory must be populated in pairs
|
Memory Type |
- DDR2 400MHz buffered (registered) ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
|
DIMM Sizes |
|
Memory Voltage |
|
Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 Single Device Data Correction (SDDC)
|
|
 |
Chipset |
- Intel® E7320 chipset
- MCH + 6300ESB + PXH +82541PI
|
SATA |
- 6300ESB SATA Controller (2x Drive support)
- 2x SATA Ports
- RAID 0, 1, JBOD support
|
SCSI |
- Broadcom 1020 U320 SCSI Controller
- Single-Channel Ultra320 SCSI
- Support for Integrated Mirroring
|
IPMI |
|
Network Controllers |
- Dual Intel® 82541PI Single Port Gigabit Controllers
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
|
Graphics |
- ATI Rage XL SVGA PCI video controller with 8 MB of video memory
|
Super I/O |
|
|
 |
Serial ATA |
- Two Serial ATA ports
- Two SATA hard drives supported
|
IDE |
- Dual EIDE channels support up to four UDMA IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
|
Floppy |
- 1 Floppy controller; 1.44 MB, 2.88 MB, 3-mode support
|
LAN |
|
USB |
- 2x USB rear ports
- 2x USB internal headers
- USB 2.0 Compliant / 1.1 Compliant
|
VGA |
|
Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
Serial Ports |
- 1 Fast UART 16550 serial port
- 1 header
|
Parallel Port |
- 1 ECP / EEP parallel port header
|
|
 |
 |
|
1U |
** NOTE: Installation of Paxville Dual Core Xeon CPUs require a 500W or higher wattage power supply.
|
Important Chassis Notes |
- To ensure system stability with non-Paxville CPUs, a 420W (minimum) ATX 12V/EPS12V power supply [4-pin (+12V), 8-pin (+12V) and 24-pin] is required for systems built with non-Supermicro chassis / power supplies.
- To ensure system stability with Paxville CPUs, a 500W (minimum) ATX 12V/EPS12V power supply
[4-pin (+12V), 8-pin (+12V) and 24-pin] is required.
- Chassis must have CPU mounting holes required for 800MHz FSB CPUs with this serverboard.
|
|
 |
PCI-Express |
|
PCI-X |
- 1x 64-bit 133MHz PCI-X (3.3V) slot
- 1x 64-bit 100MHz PCI-X (3.3V) slot
|
PCI |
- 1x 32-bit 33MHz PCI (5V) slot
|
|
 |
BIOS Type |
- 8Mb Flash EEPROM with AMI® BIOS
|
BIOS Features |
- Plug and Play (PnP)
- SMBIOS 2.3
- APM 1.2
- DMI 2.1
- ACPI 1.0
|
|
 |
Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
|
Power Configurations |
- ACPI/APM Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- CPU Fan auto-off in sleep mode
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
|
|
 |
Voltage |
- Monitors for CPU Cores, +3.3V, +5V, ±12V & +5V Standby
- CPU Core 3-Phase-switching voltage regulator with auto-sense from 1.3V-1.5V
- Adjustable CPU clock frequency ratio settings (via BIOS)
|
FAN |
- Total of six 4-pin fan headers
- 6x fans with status monitoring
- Status monitor with firmware/software on/off control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
|
Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) support
|
LED |
- CPU Overheat LED
- System Overheat LED
- Suspend-state indicator LED
|
Other Features |
- Chassis intrusion detection
- Chassis intrusion header
- Processor protection support
|
|