 | |
 | | SYS-6026TT-HDTRF | - SuperServer 6026TT-HDTRF (Black)
| | | | | CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit Xeon® processor(s) of the same type below:
- Intel® Xeon® Processor X5600/E5600/L5600 Series
(Westmere) 40W - 130W
- Intel® Xeon® Processor X5500/E5500/L5500 Series
(Nehalem-EP) 38W - 95W
| | QPI | | | | | | Memory Capacity | - 12x 240-pin DIMM slots
- Supports up to 192 GB** 1333 / 1066 / 800MHz DDR3 ECC Registered memory
- Supports up to 48 GB 1333 / 1066 / 800MHz DDR3 ECC / Non ECC Unbuffered memory
- Memory Mirroring supported
| | Memory Type | - 1333 / 1066 / 800MHz ECC Registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
| | DIMM Sizes | - 1GB, 2GB, 4GB , 8GB** , 16GB**
| | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
| | | |
| | Chipset | - Intel® 5500 (Tylersburg) chipset
- ICH10R
| | SATA | - Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
| | Network Controllers | - Dual Intel® 82574L Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
| | Graphics | | | Super I/O | | | Clock Generator | | | | |
| | Serial ATA | - Six Serial ATA ports
- 6 SATA hard drives supported
| | LAN | - 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
| | USB | - 2 rear + 1 header (2 Ports)
- 4 total USB ports, 2.0 Compliant / 1.1 Compliant
| | VGA | | | Serial Port | - 1 Fast UART 16550 serial port
| | | | | BIOS Type | - 32Mb SPI Flash EEPROM with AMI® BIOS
| | BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
| | | | |
| | Form Factor | | | Model | | | | |
| | Height | 3.5" (89mm) | | Width | 17.2" (437mm) | | Depth | 28.5" (724mm) | | Gross Weight | 85 lbs (38.6kg) | | Available Colors | Black | | | |
| | Buttons | - Power On/Off button
- UID button
| | LEDs | - Power LED (on power button)
- Network activity LED
- System Overheat/fan fail/power fail/ LED
- UID LED (on UID button)
| | | | | PCI-Express | - 2 (x8) PCI-E (FH/HL) w/ riser card (in x16 slots)
| | | |
| | Hot-swap | - 6x 3.5" SATA Hot-swap drive bays
| | | |
| | 2U Hard drive Backplane | | | |
| | Fans | | | | | | 1400W high-efficiency (1+1) redundant power supply with PMBus | | AC Input | - 1100W Output @ 100-140V, 13.5-9.5A, 50-60Hz
- 1400W Output @ 180-240V, 9.5-7.0A, 50-60Hz
| | DC Output | - 1100W: +12V/92A; +5Vsb/4A
- 1400W: +12V/116A; +5Vsb/4A
| | With Distributor | - +5V: 30 Amp
- +3.3V: 24 Amp
- -12V: 0.6 Amp
| | Certification | 
Gold Certified
[ Test Report ] | | | |
| | CPU | - Monitors for CPU Cores,+1.5V, +3.3V, +5V, +12V, +5 Stdby, +3.3 Stdby, VBAT, Memory Voltages.
- CPU Core 6-Phase-switching voltage regulator
| | FAN | - Total of four 4-pin PWM fans
- 4x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 4x Fan Connectors
- PSU I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - Power Fail / Overheat LED
- Suspend-state Indicator LED
- UID LED
| | Other Features | | | | RoHS
| | | Environmental Spec. | - Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
| |
