 |
|
|
|
|
|
|
|
|
|
Key Features
1. Highest Density 5U 8-Way Server;
Super-High Computing Performance
2. 8x Intel® Xeon® 8-core 7500^
series and 10-core E7-8800 family
processors supported
3. 64x DIMM slots support up to
2TB Reg. DDR3 ECC SDRAM**
4. 4x PCI-E 2.0 x16 + 2x PCI-E 2.0 x8
(in x16 slot) or 10x PCI-E 2.0 x8
full-height full-length slots
5. Dual Gigabit Ethernet LAN ports
6. 16x 2.5" HDDs and 2x 5.25" devices;
up to 24x 2.5" HDDs with optional
HDD module***
7. 6x SATA2 ports onboard
8. Onboard BMC supports IPMI 2.0 +
KVM with dedicated LAN
9. 6x 9cm Hot-swap cooling fans
10. 2800W hot-swap (2+2) redundant
high-efficiency power supplies
Gold Level Certified
|
|
|
Complete System Only: To maintain quality and integrity, this product is sold only as a completely-assembled system
(including but not limited to CPU, memory, and HDDs).
|
|
 |
|
|
|
|
|
|
|
 |
| SYS-5086B-TRF |
- SuperServer 5086B-TRF (Black)
|
| |
|
|
X8OBN-F (1) + X8OBN-CPU (4) + X8OBN-BR1 (2) |
| |
|
| CPU |
- Octal 1567-pin LGA Sockets
- Supports up to eight Intel® Xeon® 64-bit processor(s) of the same type below:
- Intel® Xeon® processors 7500^ series (8-core, codename Nehalem-EX) and new generation Intel® Xeon® processors E7-8800 family (10-core, codename Westmere-Ex) supported
|
| QPI |
|
| |
|
| Memory Capacity |
- 64x 240-pin DIMM sockets
- Supports up to 2048 GB DDR3 ECC reg. memory
|
| Memory Type |
- 1333* / 1066 / 978 / 800MHz ECC Registered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
- 1GB, 2GB, 4GB, 8GB, 16GB, 32GB**
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel® x4 and x8 Single Device Data Correction (SDDC)
|
| |
|
| Chipset |
- 2x Intel® 7500 (Boxboro-EX) chipset
- ICH10R
|
| SATA |
- Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support (Windows)
- RAID 0, 1, 10 support (Linux)
|
| IPMI |
- Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
|
| Network Controllers |
- Intel® 82576 Dual-Port Gigabit Ethernet Controllers
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY
(dedicated IPMI)
|
| Graphics |
|
| Super I/O |
|
| |
|
| LAN |
- 3x RJ45 LAN ports (1 for IPMI)
|
| USB |
- Total of 8 USB 2.0 ports (2x rear,
4 via 2x internal headers, 2x Type A)
|
| SATA |
|
| Serial Port / Header |
- 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
|
| VGA |
|
| |
|
| BIOS Type |
- 32Mb SPI Flash EEPROM with AMI® BIOS
|
| BIOS Features |
- Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
|
|
|
|
|
| Form Factor |
|
| Model |
|
| |
|
|
| Height |
|
| Width |
|
| Depth |
|
| Weight |
- Gross Weight: 176 lbs (79.83 kg)
|
| Available Colors |
|
| |
|
|
| Hot-swap |
|
| Peripheral Bay(s) |
|
| |
|
| PCI-Express |
- 4x PCI-E 2.0 x16 + 2x PCI-E 2.0 x8 (in x16) or
10x PCI-E 2.0 x8 full-height, full-length slots
|
| |
|
|
| Fans |
- 4x Hot-Swap Cooling Fans
- 2x Hot-Swap Rear Exhaust Fan
|
| Shrouds |
- 4x CPU card air shrouds for SC758
|
| |
|
|
| 2800W (2+2) Redundant 1400W high-efficiency power supply with PMBus |
| AC Input |
- 1200W: 100 - 140V, 50 - 60Hz, 10.5 - 14.7 Amp
- 1400W: 180 - 240V, 50 - 60Hz, 7.2 - 9.5 Amp
|
DC Output
+5V standby |
|
DC Output
+12V |
- 100 Amp @ 100-140V
- 117 Amp @ 180-240V
|
| Certification |
Gold Certified
[ Test Report ]
|
| |
|
| CPU |
- Monitors for CPU Cores, +1.2V, 1.5V, +3.3V, +12V, (+3V, 1.0V, 1.2V, 1.8V, 1.1V) Standby, VBAT, Memory, Chipset Voltages.
- 4-Phase-switching voltage regulator with auto-sense from 0.6V-1.35V
|
| FAN |
- 10x 4-pin fan headers with tachometer status monitoring
- Low noise fan speed control mode
|
| Temperature |
- Monitoring for CPU and system environment
- Thermal Control for 10x fan connectors
|
| Other Features |
- Chassis intrusion detection
|
| |
|
|
| Environmental Spec. |
- Operating Temperature:
10° to 35° C (50° to 95°F)
- Non-operating Temperature:
-40° to 70° C (-40° to 158° F)
- Operating Relative Humidity:
8% to 90% (non-condensing)
- Non-operating Relative Humidity:
5% to 95% (non-condensing)
|
|
|
|
|
 |
|
|
|
|
|
|
| |
Part Number |
Qty |
Description |
| Motherboard / Chassis |
MBD-X8OBN-F
MBD-X8OBN-CPU
MBD-X8OBN-BR1
CSE-758A-R2800BP |
1
4
2
1 |
X8OBN base board (for server SKU only)
X8OBN processor board (for server SKU only)
X8OBN bridge board (for server SKU only)
SC758 incomplete 5U Chassis (for server SKU only) |
| Backplane |
BPN-SAS-I28A |
2 |
8-port Mobile-Rack hot swappable HDD backplane (W/ 2x vertical iPass), support up to 8x 2.5-inch SAS/SATA HDD |
| Cable 1 | CBL-0116L |
2 |
IPASS TO 4SATA,CROSS OVER, 50CM, PBF |
| Cable 2 | CBL-0449L |
2 |
HDD power extension for X8OBN, special 8pin to 4 HDD |
| CD |
CDR-X8-O |
1 |
Driver CD for X8-O series motherboard |
| Heatsink / Retention |
SNK-P0044P+ |
8 |
Special CPU heatsink for Nehalem-EX |
| I/O Shield |
MCP-260-00027-0N |
1 |
Std I/O shield for X8, H8, X7SB3 server MB (3rd LAN + 4x LAN) |
| Mounting Rails |
MCP-290-00057-0N |
1 set |
Rail set, quick/quick, default for 4U 17.2"W |
|
|
|
|
|
|
| |
Part Number |
Qty |
Description |
| Mounting Rail |
MCP-290-00058-0N |
- |
Short rail set, quick/quick, optional for 2~4U 17.2"W |
| Add on cards |
AOC-SAS2LP-H8iR
AOC-SAS2LP-H4iR
AOC-STGN-i2S
AOC-E10GSFPSR
AOC-MHQH29B-XTR
AOC-MHQH29C-XTR
AOC-QLE2562 |
-
-
-
-
-
-
- |
2108 based SAS/SATA RAID- 8 internal ports/Low profile-PCI-E
2108 based SAS/SATA RAID- 4 internal ports & 4 external ports
STD Dual-port 10G Ethernet with SFP+ W/ CDR
OPTI MOD 10G SR/1000BASE-SX FOR E10G42BTDA
MHQH29B-XTR,IB 2-P QDR,PCIe2.0,QSFP,PBF
MHQH29C-XTR,IB,2-p,QDR,PCIe2.0,QSFP,PBF
QLOGIC QLE2562 2-port 8Gb Fibre Channel PCI-E |
| HDD Module |
CSE-M28SAB-OEM |
- |
SAS Mobile Rack CSE-M28SAB w/o fan module |
| Cable |
CBL-0281L |
- |
IPASS TO IPASS 75CM PBF |
| Cable |
CBL-0333L |
- |
6+2pin GPU power extension from MB GPU 8pin, 40cm |
|
|
|
^ Supported 7500 series processors include X7560, X7550, E7540, L7555, L7545, X7542 only
* Run at speed - 1066MHz
** Please check Tested Memory List for compatibility; 4Gb DRAM, 32GB or 1.35V memory requires rev 2.01 or above boards with Millbrook II
*** Additional RAID/HBA card and cables may be required (for detail, please consult with Supermicro sales representative)
|
|
|
|
