================================================= | Release Notes for SSE-F/X3548 Switch Firmware | ================================================= Release Version: 1.4.2.3 Release Date : 02/11/2025 Firmware filenames : SSE-3548-fw-1.4.2.3.installer SSE-3548-fw-1.4.2.3.swi Changes in this release: 1. PB Issue# 97447: Login authentication webpage is vulnerable to stored XSS attack. 2. PB Issue# 42011: The TTL values for eBGP multihop message is not set correctly. 3. PB Issue# 188220: BGP could not establish neighbor with Ixianvl while using 4 byte ASN test. 4. Switch crashes when the privilege password is entered after deleting the enable password. This issue is fixed. 5. Added the range value 3-9 for the 'clear cli sessions' command. 6. The command "show system environment power" is enhanced to display the psu status as "Not Present" when the power supply is removed. 7. The transceiver page in WEBUI is enhanced to read the transceiver informations with optimal use of CPU. 8. Enhanced the handling of ping requests received in data path on a VLAN interface. 9. Reload command enhanced. Now reload command support scheduling the reload in future. Command: reload [{schedule {at [{month <1-12> day <1-31>}] | after } | force | cancel}] ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.2.2 Release Date : 04/25/2024 Firmware filenames : SSE-3548-fw-1.4.2.2.installer SSE-3548-fw-1.4.2.2.swi 1. Issue#100602 : Fix for RIP neighbor 2. Fix for mrouter function test cases with wrong packet pattern ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.2.1 Release Date : 03/08/2024 Firmware filenames : SSE-3548-fw-1.4.2.1.installer SSE-3548-fw-1.4.2.1.swi 1. Issue#171784 : When try to download copy debug files switch is crashing 2. Issue#170803 : Configuring speed change X3548 isn't being reflected in the running config 3. Issue#102404 : OSPF - DUT accept route with invalid address 127.51.0.0 4. Issue#100429 : OSPF: CLI " show ip ospf X.X.X.X database adv-router Y.Y.Y.Y", CLI "show ip ospf database" 5. Issue#95658 : Missing the switch model type S or SR shown on both CLI/ Web Gui. 6. WebGui : Delete the sessions which are timeout every 10sec. 7. WebGui : Fix for users displayed in show users after logout click at sametime 8. Issue#170803 : Fix split CX with 10G no show speed setting issue. 9. Fix 25G Box SFP/QSFP fiber transceiver DOM info dump issue. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.2.0 Release Date : 01/09/2024 Firmware filenames : SSE-3548-fw-1.4.2.0.installer SSE-3548-fw-1.4.2.0.swi 1. ARP module enhanced to respond only with virtual VRRP MAC for the ARP queries for virtual VRRP IP. 2. ARP entries for virtual VRRP MAC will be flushed while transitioning from VRRP master to backup or vice versa. 3. In some cases, after few days the switch stops processing L3 packets on some VLAN interfaces. Now L3 VLAN interfaces are fine tuned for handling high traffic loads. 4. The link-scan is fine tuned to increase the reliability of bringing up the link. 5. The 'show transceiver' command enhanced to display the output faster. 6. Fixed the TOS/DSCP marking. 7. Some of the 3rd party LLDP neighbor devices were not displayed. This issue is now fixed. 8. The 'show protocol counters' enhanced to display the statistics for individual VLANs. 9. The ‘ip igmp snooping multicast filtering’ command is enhanced to exclude the mrouter port from filter. Command: ip igmp snooping multicast filtering {enable | disable | exclude-mrouter-port} 10. Password policy command added to enforce password standards and expirations. Commands: password-policy account-expire number-of-days password-policy account-lockout failure-attempt duration password-policy mandatory numeric-char special-char password-policy maximum-password-length-allowed password-policy minimum-password-length-allowed password-policy password-expire number-of-days 11. Logging configurations command added to log all the commands executed under configuration terminal mode. 12. The 'clear web session' command is introduced to clear the user sessions logged in to switch's WEBUI. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.1.1 Release Date : 07/06/2023 Firmware filenames : SSE-3548-fw-1.4.1.1.installer SSE-3548-fw-1.4.1.1.swi 1. Enhanced Jumbo frame handling. 2. Support for TLS-1.2 and TLS-1.3 is added. The TLS-1.0 and TLS-1.1 are deprecated and not supported. 3. Allowed value range is changed to [0-7] in ACL TOS. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.1.0 Release Date : 04/24/2023 Firmware filenames : SSE-3548-fw-1.4.1.0.installer SSE-3548-fw-1.4.1.0.swi 1. Upgraded the Marvell CPSS drivers to 4.3.2. 2. ACL code is enhanced. 3. Improved the logic for handling the login username and password. 4. Unable to reconfigure the port-channel 4094. This issue is now fixed. 5. CLI command 'show interfaces link parameters' is added to display the physical parameters of the link. 6. The techsupport is enhanced to include more info such as core files and configuration files. 7. Extended 'show transceiver diagnostics' command to support Cx-ethernet ports. 8. Host resource MIB for SNMP is added. 9. VLAN range command improved to throw error if the first value in the range is larger than second value. 10. Login banner and MOTD (Message of The Day) feature for CLI is added. 11. The 'show system environment' is enhanced to display more CPU, fan, power supply, and temperature Sensor parameters. 12. RESTCONF query enhanced to support longer descriptions for interfaces and more values in allowed trunk VLANs. 13. The 'ip arp max-retries is now fixed. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.13 Release Date : 01/25/2023 Firmware filenames : SSE-3548-fw-1.4.0.13.installer SSE-3548-fw-1.4.0.13.swi 1. In some cases, VLAN pruning in trunk port blocks the control packet traffic. This issue is now fixed. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.12 Release Date : 12/22/2022 Firmware filenames : SSE-3548-fw-1.4.0.12.installer SSE-3548-fw-1.4.0.12.swi 1. Added support for 512 VLAN interfaces. 2. The link stays UP on the host side after shutting down the switch port via SNMP. This issue is now fixed. 3. SNMP walk from FreeBSD server using the tool bsnmpwalk could not walk through some OIDs. This issue is now fixed. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.11 Release Date : 08/15/2022 Firmware filenames : SSE-3548-fw-1.4.0.11.installer SSE-3548-fw-1.4.0.11.swi 1. Enhanced the MLAG code to improve the failover response time when one of the MLAG partner switch fails. 2. The severity level of the log for successful login is changed from critical to info. 3. The physical state of the port is not changed when port-channel is shutdown from WEBUI. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.10 Release Date : 07/14/2022 Firmware filenames : SSE-3548-fw-1.4.0.10.installer SSE-3548-fw-1.4.0.10.swi 1. Fixed the layout of MLAG interface status page in WEBUI. 2. In some uses cases with windows OS, the MLAG enabled port-channel doesn't come up. This issue is now fixed. 3. The link status LED on the partner device stays on if the switch port is shutdown from WEBUI. This issue is now fixed. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.9 Release Date : 05/25/2022 Firmware filenames : SSE-3548-fw-1.4.0.9.installer SSE-3548-fw-1.4.0.9.swi 1. Fixed the broken bgp update filter command. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.8 Release Date : 04/28/2022 Firmware filenames : SSE-3548-fw-1.4.0.8.installer SSE-3548-fw-1.4.0.8.swi 1. Port-channel configured with LACP short timeout flaps when connected with FreeBSD. This issue is now fixed. 2. VRRP is now fine tuned to handle the ARP better in MLAG scenarios. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.7 Release Date : 01/14/2022 Firmware filenames : SSE-3548-fw-1.4.0.7.installer SSE-3548-fw-1.4.0.7.swi 1. Switch reboots while doing SNMPwalk on the entPhysicalName. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.6 Release Date : 01/12/2022 Firmware filenames : SSE-3548-fw-1.4.0.6.installer SSE-3548-fw-1.4.0.6.swi 1. Fixed the switch crash caused by invalid HTTP requests, which rarely results in losing the configuration. 2. Switch reboots while trying to establish a new SSH session when there are already few telnet sessions. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.5 Release Date : 12/20/2021 Firmware filenames : SSE-3548-fw-1.4.0.5.installer SSE-3548-fw-1.4.0.5.swi 1. Fixed a random crash issue found in web access. Upgraded underlying web related SSL libraries to latest version. 2. Enhanced the MAC address handling and ARP handling in MLAG scenarios. 3. Fixed the status sync issue for the MLAG enabled port-channel between the MLAG peers. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.4 Release Date : 09/22/2021 Firmware filenames : SSE-3548-fw-1.4.0.4.installer SSE-3548-fw-1.4.0.4.swi 1. When local MLAG port channel comes up, the IPL forwarding state was not set correct. This issue is now fixed. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.3 Release Date : 08/26/2021 Firmware filenames : SSE-3548-fw-1.4.0.3.installer SSE-3548-fw-1.4.0.3.swi 1. Sometimes the memory corruption is caused by MAC sync function and the switch crash. This issue is now fixed. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.2 Release Date : 08/16/2021 Firmware filenames : SSE-3548-fw-1.4.0.2.installer SSE-3548-fw-1.4.0.2.swi New major improvements: 1. If IP authorized-manager is configured, then switch denies access even for allowed IPs via data plane. 2. The switch reload command now gets executed without taking management semaphore lock. This helps in rebooting the switch if the CLI gets stuck while executing any command. 3. Sometimes CLI gets stuck while executing the command 'show logging' with large number of log entries. This is now resolved. 4. Added ‘telnet enable\disable’ command to enable or disable telnet service. By default telnet is enabled. The “show mgmt status” command added to show enable/disable status for management protocols. 5. Fixed the issue of restconf query for VLAN member ports did not display port channel members correctly when port-channel id is two or more digits (e.g. po 100, po 1234, …). 6. Improved HTTP/HTTPS requests handling to avoid potential deadlock and added “show ip http statistics” command. 7. VRRP code improved for better performance. ----------------------------------------------------------------------------------------------------------- Release Version: 1.4.0.1 Release Date : 01/20/2021 Firmware filenames : SSE-3548-fw-1.4.0.1.installer SSE-3548-fw-1.4.0.1.swi New major improvements: 1. Marvell CPSS driver is upgraded from 2018.11 to 2019.12 2. Port manager functionality from Marvell driver is now used to manage the port enable/disable and link detection. In earlier releases, these functionalities were done using traditional driver API. From this version these functions use new port manager feature for better link stability. 3. To avoid data path loops, all the data ports were kept shutdown until the switch completely boots up and restores the config, if config file is present in the flash. The port will start forwarding the traffic once the switch is fully ready. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.10 Release Date : 01/15/2021 Firmware filenames : SSE-3548-fw-1.3.0.10.installer SSE-3548-fw-1.3.0.10.swi 1. Fixed the issue of not able to ping virtual IP from a host connected to VRRP backup router in different VLAN network (not same subnet as VRRP network). ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.9 Release Date : 01/07/2021 Firmware filenames : SSE-3548-fw-1.3.0.9.installer SSE-3548-fw-1.3.0.9.swi 1. ARP and L3 packets not forwarded for the port-channel member port when it is in independent state. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.8 Release Date : 01/05/2021 Firmware filenames : SSE-3548-fw-1.3.0.8.installer SSE-3548-fw-1.3.0.8.swi 1. The switch crashes with the MLAG configuration during firmware upgrade if the peer firmware version is 1.2.0.7 or older. 2. Fixed kernel trace dump messages and switch hang issue happen over the time when the environment have hundreds of ARP entries in pending state. 3. Fixed the issue with command "no ip http port". 4. Fixed random ping failure in MLAG environment. 5. Fixed bgp show running config issue for bgp neighbor command with password configuration. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.7 Release Date : 12/9/2020 Firmware filenames : SSE-3548-fw-1.3.0.7.installer SSE-3548-fw-1.3.0.7.swi 1. The switch crashes while visiting the WEBUI System-->System Settings page, if the configuration restore is incomplete. 2. The command success status for the exit command in the BGP configuration block was not set properly. 3. Fixed the below PB issues. PB Id# 120543: The VxLAN tunnel not established properly. PB Id# 120535: Unable to establish BGP session with some vendor routers. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.6 Release Date : 12/1/2020 Firmware filenames : SSE-3548-fw-1.3.0.6.installer SSE-3548-fw-1.3.0.6.swi 1. Removed the commands as-num and router-id from global config since it is redundant and misleading. For BGP asnum use as-num command inside BGP config mode. 2. Debug is enabled for BGP and OSPF. Use the commands 'debug ip bgp' and 'debug ip ospf' with appropriate arguments to see the debug messages. 3. MLAG flooding issue caused by configuration command sequence is fixed. 4. Fixed the below PB issues. PB Id# 118981: The VxLAN UDP port value is not displayed correctly. PB Id# 118922: The VxLAN address table and mac-address-table are not updated after the host move. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.5 Release Date : 09/17/2020 Firmware filenames : SSE-3548-fw-1.3.0.5.installer SSE-3548-fw-1.3.0.5.swi 1. BGP enhanced to support 4 byte ASN. 2. New API added to RESTCONF to save the running-config to startup-config, to read startup-config and to delete startup-config using RESTCONF. 3. The username/password is enhanced to support 64 character passwords. 3. All bug fixes from 1.2.0.6 & 1.2.0.7 are included in this release. 4. Fixed the below PB issues. PB Id# 114908: The output of 'show lldp neighbors' contain special characters. PB Id# 114765: The port-channel load-balancing based on src-dest-ip and packet with different source MAC address doesn't function as expected. PB Id# 114762: The port-channel load-balancing based on dest-ip and packet with different source IP address doesn't function as expected. PB Id# 114755: The port-channel load-balancing based on dest-ip and packet with different source and destination MAC address doesn't function as expected. PB Id# 114743: The port-channel load-balancing based on src-ip and packet with different destination IP address doesn't function as expected. PB Id# 114742: The port-channel load-balancing based on src-ip and packet with different src dst MAC address doesn't function as expected. PB Id# 114738: The port-channel load-balancing based on dest-mac doesn't function as expected. PB Id# 114736: The port-channel load-balancing based on src-mac doesn't function as expected. PB Id# 113938: The command 'show ip igmp interface vlan 1' doesn't display any output after deleting and creating interface vlan 1. PB Id# 109215: Ping to host does work with 2 vlan/vni in the vxlan config. PB Id# 102404: Router should not accept invalid route addresses such as 127.51.0.0. PB Id# 100558: Router doesn't send any RIP message when RIP v1 is configured. PB Id# 100252: The OSPF virtual link with authentication doesn't work. PB Id# 100123: The OSPF link state update packet should be sent in unicast first and then in multicast. PB Id# 100116: L3 vlan interface should not be automatically added to OSPF process if an OSPF paramater on the interface is changed. PB Id# 99046: The command 'no ip routing' should be removed. PB Id# 98891: The command 'no passive-interface vlan' should be displayed in the running-config. PB Id# 98668: The command 'ip ospf authentication' should not be allowed to configure the OSPF authentication password. PB Id# 98594: OSPF debug does not yield any debug messages. PB Id# 96691: The output of 'show transceiver' command displays incorrect data for cable CBL-NTWL-0720 (40GbE to 4x10GbE/SFP+). ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.4 Release Date : 04/23/2020 Firmware filenames : SSE-F3548-fw-1.3.0.4.installer SSE-F3548-fw-1.3.0.4.swi 1.(108614): Issue fixed vxlan: learnt remote host mac appears in mac-address-table entry with vlan 4001. 2. Not to allow VTEP IP as self ID. 3. Issue related to remove/add VTEP and VNI issues fixed. NOTE: 1. WebGUI for VXLAN not yet added. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.3 Release Date : 04/06/2020 Firmware filenames : SSE-F3548-fw-1.3.0.3.installer SSE-F3548-fw-1.3.0.3.swi 1.(107829): SSH login by admin user but stay on 'user mode' issue fixed. Ignore previous release for this issue fix. NOTE: 1. WebGUI for VXLAN not yet added. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.2 Release Date : 04/02/2020 Firmware filenames : SSE-F3548-fw-1.3.0.2.installer SSE-F3548-fw-1.3.0.2.swi 1. Manually VNI configuration failed with hosts reachability issues fixed. (107662) 2. SSH login by admin user but stay on 'user mode' issue fixed.(107829) 3. Added the command "sh run int vxlan 1". 4. Remove of vxlan configuration support added. 5. show vxlan address table printing learned mac addressses only on a specific VTEP fixed. NOTE: 1. WebGUI for VXLAN not yet added. ----------------------------------------------------------------------------------------------------------- Release Version: 1.3.0.1 Release Date : 02/20/2020 Firmware filenames : SSE-F3548-fw-1.3.0.1.installer SSE-F3548-fw-1.3.0.1.swi 1. Added the VXLAN Gateway support. 2. Vxlan related commands are added to CLI. NOTE: 1. WebGUI for VXLAN not yet added. ----------------------------------------------------------------------------------------------------------- Release Version: 1.1.1.4 Release Date : 02/12/2020 Firmware filenames : SSE-F3548-fw-1.1.1.4.installer SSE-F3548-fw-1.1.1.4.swi 1. Removed the unnecessary interrupt, which could cause the switch to reboot. 2. Added ‘copy debug-files’ command. This command 3. Increased the logging buffer to hold more log entries. 4. Improved the IP ARP entry handling when the MAC learned from MLAG peer age-outs (PB# 104889). ----------------------------------------------------------------------------------------------------------- Release Version: 1.1.1.3 Release Date : 11/19/2019 Firmware filenames : SSE-F3548-fw-1.1.1.3.installer SSE-F3548-fw-1.1.1.3.swi 1. A warning will be displayed while setting the unique password in the manufacturing process. 2. Fixed the following issues: * In random cases, switch configured with IP authorized manager reboots while attempting to SSH from allowed IP address. ----------------------------------------------------------------------------------------------------------- Release Version: 1.1.1.2 Release Date : 11/12/2019 Firmware filenames : SSE-F3548-fw-1.1.1.2.installer SSE-F3548-fw-1.1.1.2.swi 1. Added support for unique factory default password of the user ADMIN for each SSE-F3548S/SR switch. The password can be found on a label stuck on the switch. Resetting to factory default configuration will reset the ADMIN password to the unique factory default password. For some reason if the label on the switch is lost, and the user needs the unique factory default password, then the user can call supermicro support and get it by providing the switch serail number. ----------------------------------------------------------------------------------------------------------- Release Version: 1.1.1.1 Release Date : 10/25/2019 Firmware filenames : SSE-F3548-fw-1.1.1.1.installer SSE-F3548-fw-1.1.1.1.swi 1. Fixed the following issues: PB Id# 101308: In CLI command 'ip pim message-interval', the interval should not include '0' in the range. The range should be '1-65535'. PB Id# 100594: The CLI command 'area 0.0.0.1 nssa defaut-information-originate' results in fatal error. PB Id# 100499: PIM Neighbors failed to recover after shut and no shut on the interface. PB Id# 99173: The CLI command to configure PIM Hello Hold Time shall be removed as the value is derived from hello interval. PB Id# 99167: Implementation for PIM Hello interval needs to be corrected. PB Id# 99142: IP address gets reversed in PIM component after a specific sequence of command execution. PB Id# 98934: OSPF 'show ip ospf' command results in error. PB Id# 98891: OSPF passive-interface default doesn't take effect. PB Id# 98669: OSPF neighbor command results in error. PB Id# 98624: OSPF adjacency not established if the VLAN interface IP is assigned without network mask. PB Id# 97466: Flow-control doesn't work for traffic with priority tags. PB Id# 96615: Removing LLDP config using interface range command takes effect only for the first interface. PB Id# 93731: 'Root Resource Discovery' should be supported in RESTCONF as per RFC8040. PB Id# 92887: An error message is displayed while configuring 10G/1G speed on FX ports with AN and FEC disabled from WEBUI. PB Id# 92885: Unable to set the Fx interface speed to 1G/10G with AN and FEC disabled from WEBUI. ----------------------------------------------------------------------------------------------------------- Release Version: 1.1.1.0 Release Date : 08/22/2019 Firmware filenames : SSE-F3548-fw-1.1.1.0.installer SSE-F3548-fw-1.1.1.0.swi 1. Fixed the following issues: PB Id# 101253: MLAG peer state is displayed as 'unknown' if large port channel number is used for port-channel id. PB Id# 100597: OSPF cli "area 0.0.0.1 nssa default-information-originate" PB Id# 100556: ping fails on all SVI IP Addresses after performing 'shut/no shut' on one vlan interface PB Id# 99608: BGP function broken when interface up/down PB Id# 99610: BGP function broken after system reload ----------------------------------------------------------------------------------------------------------- Release Version: 1.1.0.6 Release Date : 08/15/2019 Firmware filenames : SSE-F3548-fw-1.1.0.6.installer SSE-F3548-fw-1.1.0.6.swi 1. Fixed the following issues: corrected the version number on show version output for the relases code. ------------------------------------------------------------------------------------------------------------- Release Version: 1.1.0.5 Release Date : 08/02/2019 Firmware filenames : SSE-F3548-fw-1.1.0.5.installer SSE-F3548-fw-1.1.0.5.swi 1. Fixed the following issues: Enhanced the MAC handling in MLAG environments for the missing VLANs. Enhanced the packet handling by VRRP backup router in MLAG environments. ------------------------------------------------------------------------------------------------------------- Release Version: 1.1.0.4 Release Date : 07/25/2019 Firmware filenames : SSE-F3548-fw-1.1.0.4.installer SSE-F3548-fw-1.1.0.4.swi 1. Fixed the following project board issues: * Support packet handling similar to the linux hosts with larger IP MTU plus ethernet header. ------------------------------------------------------------------------------------------------------------- Release Version: 1.1.0.3 Release Date : 07/19/2019 Firmware filenames : SSE-F3548-fw-1.1.0.3.installer SSE-F3548-fw-1.1.0.3.swi 1. Fixed the following project board issues: PB Id# 98679: Switch truncates the ping response packets that are larger than the size of 9158 bytes. ------------------------------------------------------------------------------------------------------------- Release Version: 1.1.0.2 Release Date : 06/26/2019 Firmware filenames : SSE-F3548-fw-1.1.0.2.installer SSE-F3548-fw-1.1.0.2.swi 1. Fixed the following project board issues: PB Id# 98679: Routing jumbo frame through layer-3 interfaces failed. PB Id# 98598: Core dump file not saved PB Id# 98527: VRRP IP not responding after changing the VLAN tag/untag of the interface. PB Id# 98469: ARP response sent only once for VRRP IP. PB Id# 98370: The "logging facility loca2" is not restored after reboot. PB Id# 94151: show running displays the 'mlag enable' without indentation under port-channel configuration. PB Id# 93747: Unable to configure new ntp server with prefer after deleting the old preffered ntp server. ------------------------------------------------------------------------------------------------------------- Release Version: 1.1.0.1 Release Date : 04/12/2019 Firmware filenames : SSE-F3548-fw-1.1.0.1.installer SSE-F3548-fw-1.1.0.1.swi 1. Increased the device name string length to 32 characters. 2. Support for TACACS accounting is added. 3. The command ‘show tacacs’ is enhanced to show more details. 4. Terminal width and length can be adjusted using ‘terminal width’ and ‘terminal length’ commands respectively. 5. The grep command that helps to search for words in the command output is now enhanced to search for multiple words. 6. Switch software is enhanced to accept 40 characters string for user passwords. 7. Fixed the following project board issues: PB Id# 97958: Tagged ping to an IP address assigned to a vlan interface fails. PB Id# 97838: The command 'no switchport' shall be removed from CLI as router port feature is not supported yet. ------------------------------------------------------------------------------------------------------------- Release Version: 1.1.0.0 Release Date : 02/28/2019 Firmware filenames : SSE-F3548-fw-1.1.0.0.installer SSE-F3548-fw-1.1.0.0.swi 1. Support for Layer-3 routing (IPv4 only) is added in this release. Layer-3 routing protocols RIP, OSPF, BGP and VRRP are supported. Also support for multicast protocols IGMP and PIM are added. Layer-3 interface configuration (i.e. no switchport command) directly on the physical port is not supported yet. ------------------------------------------------------------------------------------------------------------- Release Version: 1.0.2.8 Release Date : 02/27/2019 Firmware filenames : SSE-F3548-fw-1.0.2.8.installer SSE-F3548-fw-1.0.2.8.swi 1. Marvell chip drivers were updated to version 4.2.2018.11. 2. Fixed the following project board issues: PB Id# 96998 : When the IGMP leave reports arrive at high rates, some reports are not forwarded as required. Now the software is enhanced to fix this issue. PB Id# 96997 : When the IGMP join reports arrive at high rates, some reports are not forwarded as required. Now the software is enhanced to fix this issue. PB Id# 96673 : Restconf: RSA key size is not long enough for SSL/TLS running on port 8538. ------------------------------------------------------------------------------------------------------------- Release Version: 1.0.2.7 Release Date : 02/05/2019 Firmware filenames : SSE-F3548-fw-1.0.2.7.installer SSE-F3548-fw-1.0.2.7.swi 1. Switch doesn't forward spanning tree BPDUs when spanning tree is disabled. 2. IGMP snooping multicast filtering can be enabled per VLAN basis. 3. SSL security is strengthened for the RESTCONF functionalities. 4. IGMP Snooping join/leave accepted on mrouter ports. 5. Fixed the following project board issues: PB Id# 96863 : Switch CLI doesn't respond after removing the channel-group from interface. PB Id# 96500 : Restconf: SSL and TLS listening on restconf port 8538 are vulnerable to POODLE attack PB Id# 96499 : Restconf: SSL and TLS listening on restconf port 8538 should support TLS_FALLBACK_SCSV PB Id# 96496 : Restconf: RC4 cipher suites should be deprecated in SSL and TLS listening on restconf port 8538 PB Id# 96494 : Restconf: SSLv3 should be deprecated in SSL and TLS listening on restconf port 8538 ------------------------------------------------------------------------------------------------------------- Release Version: 1.0.2.6 Release Date : 01/18/2019 Firmware filenames : SSE-F3548-fw-1.0.2.6.installer SSE-F3548-fw-1.0.2.6.swi 1. Unwanted 4 byte FCS was added to some frames randomly. This issue is fixed in this release. ------------------------------------------------------------------------------------------------------------- Release Version: 1.0.2.5 Release Date : 1/8/2019 Firmware filenames : SSE-F3548-fw-1.0.2.5.installer SSE-F3548-fw-1.0.2.5.swi 1. HTTPS support added for RESTCONF. From this version (1.0.2.5) only HTTPS is supported for RESTCONF. 2. Fixed the following project board issues: PB Id# 96067 Restconf : The server MUST respond the same as if the method was GET instead of HEAD, except that no response message-body is included. PB Id# 95320 Restconf : create vlan via Restapi curl cmd causes switch reboot. ------------------------------------------------------------------------------------------------------------- Release Version: 1.0.2.4 Release Date : 12/19/2018 Firmware filenames : SSE-F3548-fw-1.0.2.4.installer SSE-F3548-fw-1.0.2.4.swi 1. Fixed the following project board issues: PB Id# 95052 Restconf: Incorrect output for display logging server for rest api cmd. PB Id# 95084 Restconf : Incorrect return code for logging content all via rest api. PB Id# 95085 Restconf : using rest cmd gets Incorrect return code 501 for oc-log content=config PB Id# 95086 Restconf : Incorrect return code 501, for oc-log selector rest api command. PB Id# 95256 Restconf : LLDP tlv PATCH commad gets Incorrect return code 204. PB Id# 94701 Restconf : port Priority out of range , should show 400 bad request as response. PB Id# 95322 Restconf :Already existing MST instance ID and vlan , returns incorrect response 404 instead of 409 conflict. ----------------------------------------------------------------------------------- Release Version: 1.0.2.3 Release Date : 11/05/2018 Firmware filenames : SSE-F3548-fw-1.0.2.3.installer SSE-F3548-fw-1.0.2.3.swi 1. Fixed the following project board issues: PB Id# 93731 Restconf: Root resource discovery per RFC 8040 PB Id# 94650 Restconf: STP bridge priority passed as string value in rest api sets switch bridge priority to 0. PB Id# 93825 Restconf: return data is different than URI resource request for logging server via restapi. PB Id# 94680 Restconf: STP Port-Priority used as string value sets the interface priority to 0 via rest api. PB Id# 94642 Rest: Incorrect response code received for interface name in URL via rest api. Restconf: vlan configuration via Rest api, switch reboots. PB Id# 94248 Restconf: using three digit vlan ID as string value shows only middle digit assigned to interface via Rest api. PB Id# 94257 Restvonf: trunk vlans assignment to interface without proper syntax i.e within square bracket e.g vlan ID [678] PB Id# 94701 RestApi: MST port-priority used as string value "12345" sets to 0 on interface PB Id# 94701 Restconf: configuring MST out of range cost and port priority combination via rest api. responds 404 But changes take effect. PB Id# 94719 Restconf :configure too long mst name via rest api reboots the switch. PB Id# 94691 Restconf: MST revision configuration via rest api can take string input or out of range value and configures to value 0 PB Id# 94086 Restconf: remove PUT method from the 'Accept' header in HTTP response of the uri interface config name PB Id# 93845 Restconf: Invalid interface name passed on as string in rest api , returns incorrect response. PB Id# 94780 restconf : malformed POST method gets incorrect return code. PB Id# 94818 restconf : using Very long NTP key value reboots switch. PB Id# 95055 restconf : GET query for logging server via rest api shows incorrect source address IP. --------------------------------------------------------------------------------------------------------------- Release Version: 1.0.2.2 Release Date : 10/17/2018 Firmware filenames : SSE-F3548-fw-1.0.2.2.installer SSE-F3548-fw-1.0.2.2.swi 1. Fixed the following project board issues: PB Id# 94093 & 94091 - Provisioning LACP system priority via restapi allows string value. PB Id# 94087 - Unable to delete port channel with 3 digit port id via restapi. PB Id# 93604 - Output of get memory info via restapi doesn't match with output of 'show meminfo' CLI command. PB Id# 93926 - Restconf: Malformed POST Server Group Request via restapi results in the switch crashes. PB Id# 94245 - Restconf: provision Vlan status allows random characters using restconf api. PB Id# 94251 - Restconf: configure port VLAN for ACCESS mode allows multiple vlans PB Id# 93863 - Restconf: out of range MTU allowed using restapi. PB Id# 94206 - Restconf: Get vlan via rest command reboots switch. PB Id# 94149 - Restconf : configure mlag system priority allows string value via restapi. PB Id# 93568 - Restconf : switch name modify via restapi PUT commmand does not work. PB Id# 94278 - Restconf : restapi get command output shows native vlan as 0 PB Id# 94038 - Restconf : GET restapi command output shows empty column for trunk vlans if interface configured with 3 or more vlans PB Id# 94033 - Restconf : restapi command for inteface mode allowed random characters with incorrect response code. PB Id# 93915 - Restconf : restapi output should not return empty resource server group in aaa get command PB Id# 93746 : NTP running config does not display NTP prefer server info. ------------------------------------------------------------------------------------------------- Release Version: 1.0.2.1 Release Date : 08/29/2018 Firmware filenames : SSE-F3548-fw-1.0.2.1.installer SSE-F3548-fw-1.0.2.1.swi 1. Enhanced QoS code to support strict priority when QoS is enabled. 2. Fixed the following project board issues: 93311 - Switch encounters segmentation fault error and reboots when 'ntp broadcast' is configured. 93028 - NTP doesn't sysnc after rebooting the switch. 93016 - Attempt to set Cx-ethernet 0/2 and 0/3 to 40G from WEBUI failed. 92962 - Hardware version is not displayed in the CLI command 'show version'. 92837 - Attempt to split Cx-ethernet 0/2 into 4x10G interfaces from WEBUI failed. 92510 - Attempt to turn ON the auto-negotiation on a Cx-ethernet interface configured at 40G sets the speed to 10G. 92506 - Remove references for unsupported 'snmpsubagent' command from CLI and user guide. 92505 - Configuring SNMP NotifyName with longer text in 'snmp notify' command makes the switch to reload. 92504 - Length of NotifyName in 'snmp notify' command should support the length mentioned in user guide. 92503 - Configuring SNMP ParamName/userName with longer text in 'snmp targetparams' command makes the switch to reload. 92502 - Configuring SNMP TargetAddressName/ParamName with longer text in 'snmp targetaddr' command makes the switch to reload. 92501 - Length of SNMP view name should be supported as mentioned in the user guide. 92500 - Configuring SNMP group/user name with longer text in 'snmp group' command makes the switch to reload. 92499 - Length of SNMP user name should be supported as mentioned in the user guide. 92498 - Configuring SNMP TransportTag with longer text in 'snmp community' command makes the switch to reload. 92497 - Length of SNMP context name should be supported as mentioned in the user guide. 92496 - Length of SNMP security name should be supported as mentioned in the user guide. 92495 - Configuring SNMP community name with longer text in command 'snmp community' makes the switch to reload. 92363 - Switch reboots if system location is configured with more than 96 characters. 92362 - Switch reboots if system contact is configured with more than 96 characters. 91301 - Turning ON FEC for interface Cx-ethernet 0/6 using WEBUI failed. 91300 - Configuring FEC-mode using WEBUI for interface Cx-ethernet 0/2 failed. 90758 - Switch doesn't honor the tagged frames for QoS strict priority. ------------------------------------------------------------------------------------------------- Release Version: 1.0.2.0 Release Date : 07/30/2018 Firmware filenames : SSE-F3548-fw-1.0.2.0.installer SSE-F3548-fw-1.0.2.0.swi 1. Added support for RESTCONF feature. RESTCONF is a RESTful protocol that provides a HTTPS interface for accessing data defined in YANG data model. Please refer to Restconf User Guide for more details. 2. Fixed the following project board issues: 92033 - The port numbers displayed in the dashboard GUI is not aligned properly to the corresponding ports. 92029 - CRC errors encountered when Cx-ethernet port is split into 10G. 91297 - In WEBUI, FEC mode field is displayed as empty when the port speed is set to 10G. 90330 - Transceiver information not displayed in WEBUI. 89517 - Encountered frame loss in Fx-ethernet ports. ------------------------------------------------------------------------------------------------- Release Version: 1.0.1.6 Release Date : 06/22/2018 Firmware filenames : SSE-F3548-fw-1.0.1.6.installer SSE-F3548-fw-1.0.1.6.swi 1. Important Note: File system enhancements were done in this release, so please upgrade to 1.0.1.6 release from ONIE shell using 'SSE-F3548-fw-1.0.1.6.installer' image. 2. Fixed unwanted messages displayed while configuring the switch with static IP address. 3. Fixed the following project board issues: 91707 - Startup configuration is lost after power cycle. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against Cx ports in WEBUI may be incomplete. 3. Support to split Cx ports from WEBUI will be added soon. ------------------------------------------------------------------------------------------------- Firmware filenames : SSE-F3548-fw-1.0.1.5.installer SSE-F3548-fw-1.0.1.5.swi Release Version: 1.0.1.5 Release Date : 06/15/2018 1. The 'ip access-group' and 'mac access-group' commands, which are used to apply ACL to specific interfces, are changed. Now users don't need to mention 'in'. By default the ACL is applied to ingress traffic of that interface. See below examples. Examples: ip access-group 200 mac access-group ServerMacGroup 2. Speed command enhanced to check whether auto-negotiation is turned off before configuring Fx interfaces to 10G. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against Cx ports in WEBUI may be incomplete. 3. Support to split Cx ports from WEBUI will be added soon. ------------------------------------------------------------------------------------------------- Firmware filenames : SSE-F3548-fw-1.0.1.4.installer SSE-F3548-fw-1.0.1.4.swi Release Version: 1.0.1.4 Release Date : 06/13/2018 1. Improved auto-tuning to bring up the link faster. 2. FEC and negotiation are turned ON for all Fx and Cx ports by default. 3. Added support for splitting Cx ports. Each Cx ports can be split into 4 10G ports or 4 25G ports. Use the speed command to split the Cx ports. For example, the command 'speed 25000' will split the Cx port into 4 25G ports. For further details refer to configuration guide. 4. Added support for flowcontrol. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against Cx ports in WEBUI may be incomplete. 3. Support to split Cx ports from WEBUI will be added soon. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.1.3.installer SSE-F3548-fw-1.0.1.3.swi Release Version: 1.0.1.3 Release Date : 05/10/2018 1. This is an internal release with no code change. Only version number is changed. This release is made for internal test purposes. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against ports in WEBUI may be incomplete. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.1.2.installer SSE-F3548-fw-1.0.1.2.swi Release Version: 1.0.1.2 Release Date : 05/10/2018 1. F3548 switches can be upgraded in traditional way from CLI using the 'firmware uprade' command. Upgrade from WEBUI is not supported yet. For upgrading in the traditional way use the file with extension 'swi'. 2. Fixed the following project board issues: 90603 - Cx-ethernet ports goes down after few interface operations such as enabling and disabling auto-negotiation. 90099 - File system in flash storage gets corrupted sometimes when the switch boots up. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against ports in WEBUI may be incomplete. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.1.1.installer Release Version: 1.0.1.1 Release Date : 05/02/2018 1. Fixed the following project board issues: 90276 - Cx-ethernet ports link not stable when connected to some ports on some vendor switches. This symptom is a corner case and doesn't occur with all vendors or all ports. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against ports in WEBUI may be incomplete. 3. Auto negotiation is not validated fully. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.1.0.installer Release Version: 1.0.1.0 Release Date : 04/17/2018 1. SDK libraries updated to latest version 2018.2. 2. by default auto-negotiation and fec-mode are turned on for Fx ports. 2. Fixed the following project board issues: 89503 - Serial number and revision information were not displayed for Fx ports in 'show transceiver' command output. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against ports in WEBUI may be incomplete. 3. Auto negotiation is not validated fully. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.0.4.installer Release Version: 1.0.0.4 Release Date : 04/13/2018 1. Fixed the following project board issues: 89967 - Switch doesn't respond to SNMP queries. 89965 - SSH to switch fails when IP authorization manager is configured to allow SSH service. 89512 - LED doesn't light up for port Fx 0/46. 89511, 89504 - When some Fx ports are connected, LED lights up against wrong port instead of connected port. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information displayed against ports in WEBUI may incomplete. 3. Auto negotiation is not validated fully. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.0.3.installer Release Version: 1.0.0.3 Release Date : 04/04/2018 1. SSH issue is fixed and now user can SSH from windows computers. 2. The 'show interface' command output is enhanced to display whether FEC mode is set to on/off. 3. Fixed the following project board issues: 89498 - 'show transceiver' command yields a slow response. Known issues: 1. Hardware version/revision not displayed in CLI/web. 2. Transceiver information may be displayed against incorrect ports in web. 3. Auto negotiation is not validated fully. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.0.2.installer Release Version: 1.0.0.2 Release Date : 03/19/2018 1. Fixed the following project board issues: 88825 - Switch reboots when an invalid interface type is entered in 'interface range' command. Known issues: 1. SSH from windows may not work. 2. Hardware version/revision not displayed in CLI/web. 3. Transceiver information not available in web. Sometimes switch may hang if the transceiver web page is loaded. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.0.1.installer Release Version: 1.0.0.1 Release Date : 03/08/2018 1. Improved the link stability for Fx/Cx ports. 2. Fixed the following project board issues: 88834 - Reset-to-factory-defaults command does not work on CLI / WEB GUI. 88824 - Show running-config should not shown 48 port 25ge with the wrong speed 10ge by default. 88003 - [F3548-1.0.0.0] [Data path] Interface on 10G speed data forwarding unstable, ramdonly down. 88002 - [F3548-1.0.0.0] [Interface] No link-up, no data path function on 100G interface with IXIA 88000 - [F3548-1.0.0.0] [Interface] No link-up, on 100G interface with C3632 (cumulus). 87999 - [F3548-1.0.0.0] [Interface] No link-up, on 25G Interface. 87998 - [F3548-1.0.0.0] [SSH] Unstable SSH, Automation abort due to SSH failed. 87580 - Switch console hangs sometimes while trying to write to startup-config. 87579 - Default speed on Fx-ethernet ports should be 25G. 87578 - Packets not transmitted sometimes after interface speed changes. Known issues: 1. SSH from windows may not work. 2. FEC-mode, when configured, doesn't show up in running-config. 3. Hardware version/revision not displayed in CLI/web. 4. 'show processes cpu' doesn't yield an output. 5. Transceiver information not available in CLI/web. ------------------------------------------------------------------------------------------------- Firmware filename : SSE-F3548-fw-1.0.0.0.installer Release Version: 1.0.0.0 Release Date : 01/11/2018 This release is intended for internal testing. The software is not fully ready.